Product category:
Level and tank contents instrumentation
News Release from: Hoerbiger-Origa | Subject: RCS Filling Machines
Edited by the Processingtalk Editorial
Team on 18 August 2005
Soap filling machines don't work up a
lather
RCS Filling Machines has harnessed the precision movement capabilities of rodless pneumatic cylinders for handing delicate liquids that can froth or foam in an instant
RCS Filling Machines has harnessed the precision movement capabilities of rodless pneumatic cylinders for handing delicate liquids that can froth or foam in an instant Manufacturers of soaps, detergents and the many other products that can foam-up have to take particular care when it comes to the final packaging or filling stage of their manufacturing operation
This article was originally published on Processingtalk on 14 Jan 2003 at 8.00am (UK)
Related stories
From a single valve to I/P converters
The intrinsically safe Hoerbiger-Origa Piezo valve with a switching power rating of only 1 mW is the basis of the whole modular product range of Low-Power Systems
Pressure regulation goalposts move again
Hoerbiger-Origa has enhanced its intelligent proportional pressure control valve, Airfit Tecno, with a redesign improving its performance and ensuring reliability in the most arduous application zones
Many turn to Nottingham-based RCS Filling to develop bespoke machines that allow them to maintain production speeds yet be confident of successful filling.
The basic technique employed by RCS is to keep the dispensing nozzle just below the surface of the liquid as it fills the drum.
This is done using a rodless cylinder made by Hoerbiger-Origa to raise the nozzle at a precisely regulated speed.
Further reading
Modular valve island has multipole connection
Hoerbiger-Origa has developed a valve island with an integrated multipole connection, for use in controlling multi-axis pneumatic systems, using the Hoerbiger-Origa S10 range of valves
Downsizing ready for the Nano revolution
The NZ range of compact pneumatic cylinders has been extended by Hoerbiger-Origa to embrace more small-bore sizes, pre-empting the new standard ISO 21287 that comes into effect later this year
Perfect cast iron cylinder liner for engine blocks
An even coating of a ceramic die dressing is the key to the consistent production of perfect cast iron cylinder liners for engine blocks at GKN Sheepbridge Stokes in Chesterfield
In use, empty drums are delivered to the filling station, usually by conveyor, and the rodless cylinder lowers the filling nozzle into the drum to a point just above its bottom.
Delivery begins slowly, but once the nozzle is immersed in liquid it can speed up.
If the nozzle were to stay in a static position back pressure would soon build up and slow down delivery.
Therefore the nozzle begins to retract at a rate proportional to the delivery flow such that it always remains just below the surface.
Normally the drum is cylindrical, so the rate of retraction is a steady speed, relatively easy for RCS to set up.
This can be achieved with an open loop control algorithm, although RCS prefer to close the loop using a load cell to constantly weigh the amount of liquid that has been delivered and convert this into an exact determination of the level in the drum.
However, if the drum is of a profiled shape the rate of the rise in level is non-linear and either a specific control algorithm has to be developed or the level monitored in real time.
In either case RCS has to be confident that the Origa cylinder can accurately maintain position.
Once filling is complete the nozzle has to retract fully to allow capping to proceed to complete the cycle.
"Typically we'll insert the nozzle rapidly, raise it slowly during filling, then complete the final retraction at high speed," explains RCS Technical Director Stuart Margetson.
"It's quite a demanding duty cycle in a tough environment and operation may well be 24x7.
We use the Origa cylinder because it was the original rodless and has an enviable track record".
The Origa has three other major advantages appreciated by the RCS designers.
Its robust design allows it to be used as a structural element of the machine, reducing the amount of support engineering needed considerably.
The design is identical for all sizes from the smallest 16mm bore to the largest 48mm, which means RCS can use the same design details for all their machines regardless of overall size.
Finally the stroke length is infinitely variable up to 3m as standard, again rationalising machine design for RCS.
Pneumatic actuation is critical for RCS because many times the working environment is Zone 1 or Zone 2 explosive, where sparks from electrically driven actuators could be disastrous.
Hoerbiger-Origa pneumatic cylinders satisfy the demands of today's ATEX regulations for explosive atmospheres, and equivalent regulations in other territories.
Some RCS machines have multiple nozzles for simultaneously filling a number of drums, and in others the nozzles have to be able to index in x and y directions to fill drums on pallets.
Such machines will typically use several Origa cylinders to provide the necessary three dimensional movements. Request a free brochure from Hoerbiger-Origa ...
• Hoerbiger-Origa: contact details and other news
• Email this article to a colleague
• Register for the free Processingtalk email newsletter
• Processingtalk Home Page
Search the Pro-Talk network of sites
