Product category:
Sludge Handling and treatment
News Release from: Mono Pumps | Subject: Mono Industrial E Range pump
Edited by the Processingtalk Editorial
Team on 02 June 2005
Reliability on Beverley sludge at the
WwTW
Yorkshire Water reports that 8 Mono Industrial E Range pumps fitted on the autodesludge process at Beverley WwTW have completed 18 months of trouble-free operation following their installation
Yorkshire Water reports that eight Mono Industrial E Range pumps fitted on the auto desludge process at Beverley WwTW have just completed eighteen months of trouble-free operation following their installation The pumps replaced competitive products, which had to be removed after they had suffered constant blockages and unreliable service
This article was originally published on Processingtalk on 13 Jan 2003 at 8.00am (UK)
Related stories
Further Cost Savings on Mono Hygienic Pumps
Further improvement to manufacturing processes enables Mono Pumps to pass cost savings to customers in the food, chemical and pharmaceutical industries with the Hygienic S Range pumps.
New Mono coating provides answer to rotor abrasion
Mono Pumps, a leading manufacturer of pumps and pumping solutions, has launched Duracoat 3000 - a new surface coating offering increased wear resistance for rotors used in highly abrasive environments
Two Mono CE071SJR4 progressive cavity pumps are fitted to each of the four primary settlement tanks at Beverley WwTW as part of the framework agreement with Yorkshire Water, and were specified with minimum maintenance requirements and low whole of life costs uppermost in mind.
The competitor pumps had only been in operation for approx 1 year before Yorkshire Water had to resort back to manual desludging of the tanks because of constant blockages and this was proving to be cost prohibitive.
The pumps draw sludge from the bottom of the sludge hopper under the head of water in the primary tanks and transfer it to the sludge wet well.
Further reading
Mono Pumps has a slick operation for Shell UK Oil
Pumping rain water with potential hydrocarbon traces from a pipe track catchment area was solved by Mono Pumps, using a P range vertical progressive cavity, positive displacement pump
Solution to corrosion for Northumbrian Water
An unexpectedly high levels of corrosion was at the root of problems with two centrifuge cake disposal pumps, which needed frequent visits by maintenance staff at Honeyhill Water Treatment Works
Mono sump pump system at Tarmac Topblock
Mono Pumps has provided an environmentally friendly, cost effective, disposal solution for steam condensate at the Tarmac Topblock Aircrete block plant near Arundel
The previous equipment was situated in a confined place below ground, which proved inconvenient given the levels of maintenance subsequently required.
The Mono pumps are situated above ground to improve access if required, although in the event they have not suffered a single blockage in the first year and a half of operation.
The primary sludge has a dry solids concentration of 3 - 8% and all the eight pumps have a transfer rate of 15m3/h.
Powered by 3kW motors, the pumps internal fluid velocities are designed to be kept within operating limits to guarantee a long and relatively trouble free life - an assumption which has been borne out by experience.
Other characteristics which demonstrate the far sighted Yorkshire Water approach to lowering fixed costs and controlling long term budgets is the decision to have the pumps fitted with mechanical seals, rather than packed glands and to be equipped with overpressure and dry run protection systems.
Commenting on the Yorkshire Water experience of the E Range pumps at Beverley WwTW, Area Operations Supervisor David Sutton said, "The Mono equipment is trouble-free in operation and has significantly reduced the levels of maintenance required.
On this basis it entirely justifies the decision to purchase equipment with a higher specification because it gives us a lower cost of ownership".
Mono Pumps are designed to give least whole life costs through component life, reliability of operation and ease of maintainability.
Rotor and stator materials are selected and coated according to the end users industry to ensure that the type of wear likely to take place is accounted for and the best combination of materials is supplied.
Differential pressure per rotor stage is kept to a minimum.
This reduces the load at the rotor/stator seal line and consequently reduces wear.
Pump speed is selected according to the end product and is kept to the optimum and as the E Range pumps are fitted with the Mono Flexishaft coupling, wearing parts are minimised and lubrication is unnecessary, eliminating product contamination in the unlikely event of joint failure.
• Mono Pumps: contact details and other news
• Email this article to a colleague
• Register for the free Processingtalk email newsletter
• Processingtalk Home Page
Search the Pro-Talk network of sites
