Product category:
Telemetry, data acquisition + loggers
News Release from: Moore Industries International | Subject: NCS HALT test
Edited by the Processingtalk Editorial
Team on 27 April 2007
NCS Data Acquisition System baked for 2
years!
A Moore Industries NCS Data Acquisition System has been tested since February 2005 in an environmental chamber at temperatures up to 221F, to prove it will work even in Middle Eastern applications
Moore Industries has been continuously running its NET Concentrator System (NCS) data acquisition system at temperatures hovering around the boiling point of water for more than two years in an environmental chamber, just to prove a point Fred Adt, director of quality assurance at Moore Industries, explains that conventional testing and life-test procedures are not enough when products are intended for use in severe operating conditions, such as in the Middle East
This article was originally published on Processingtalk on 28 Jul 2008 at 8.00am (UK)
Related stories
Measuring boiler and furnace temperatures simply
Protection tubes and flexible sensors make it possible to replace thermocouples in boilers and furnaces, without shutting down the entire process for days or weeks
Dealing with the ATEX Directive requirements in EU
Negotiating the maze of national and international rules and regulations on hazardous area approvals is a minefield, and can extend product development project costs and times considerably
The NCS is intended for use as a remote control and data acquisition system in unheated and un-air conditioned enclosures, so it has to endure wide temperature extremes.
"The MTBF (Mean Time Between Failures) for the NCS, determined in accordance to the Bell Core reliability model, exceeds 300,000 hours at 25C," explains Adt.
But this model isn't good enough for Moore Industries.
Further reading
Measuring molasses temperature with a MII Worm
A rigid sensor couldn't measure molasses temperature accurately in a conventional thermowell, but a custom thermowell with a Worm RTD flexible sensor measure perfectly
'Special Needs and Products' for signal interfaces
Moore Industries-International has announced a revolutionary new service called SNAP, or 'Special Needs and Products' to meet unusual signal interfacing needs
Adt wants to find out how long the NCS will actually last at high temperatures.
So Adt is using the Highly Accelerated Life Test (HALT) concept, which calculates equipment life based on increased environmental stress at higher temperatures.
Running at 90C provides a factor of 6.5; that is, every hour running at 194F (90C) is equal to running 6.5 hours at normal ambient temperatures.
Fortunately, meeting the test specs was not difficult.
Moore Industries products are designed for operation at ambient temperatures of -40C to +85C, so the test is just barely above its maximum design temperature.
"HALT lets us demonstrate performance of the NCS outside its specified environmental operational envelope," explains Adt: "The idea is that any failures induced that way might be consequently eliminated by design, thus creating a product with more margin to failure.
Therefore, we have been running a continuous HALT on the NCS since February 2005, at temperatures from 90 to 105C (194 to 221F), with open air applications in the Middle East in mind".
So far, it hasn't failed.
The NCS reached a HALT-calculated MTBF of 123,240 hr in April 2007, and remains in continuous test.
The HALT accumulates about 50,000 hours per year, so the full test has less than four years to go before reaching 300,000 hr.
"We intend to reach 300,000 hours, and maybe beyond," notes Adt: "Having actually operated our product at these high temperatures should give our customers more confidence.
HALT demonstrates that our MTBF calculations and design verifications are valid so far".
The specs for the NCS HALT are:.
* Ambient Temperature: 90C (194F).
* Test Commenced: February 8, 2005.
* Models Installed: EIM, CPM, AIM, TIM, DIM, ROM.
* Operation Mode: Temperature inputs are monitored via EIM on-line and data is logged on a daily basis.
* MTBF status: 790 days times 24 hr = 18,960 hr.
According to the Arrhenius equation, the acceleration factor for 90C is 6.5.
This means a demonstrated MTBF of 123,240 hr has accumulated as of April 8.
• Moore Industries International: contact details and other news
• Email this article to a colleague
• Register for the free Processingtalk email newsletter
• Processingtalk Home Page
Search the Pro-Talk network of sites
