Product category:
Valves and manifolds
News Release from: Roxspur Measurement and Control | Subject: FCV, NGX and Flostat
Edited by the Processingtalk Editorial
Team on 08 March 2007
Precision flow control of liquids and
gases
When setting up any fluid system for sample or a purge flow, in a laboratory or a pilot plant, a manual control will be needed to stabilise the flow of liquid or gas from the supply or the pump
When setting up any fluid system, whether in a laboratory or a pilot plant, setting a sample or a purge flow, a manual control will be needed to stabilise the flow of liquid or gas from the supply or the pump Within the range of Platon variable area flowmeters, NGXV models are supplied with an integral flow control valve for this purpose
This article was originally published on Processingtalk on 4 Jan 2008 at 8.00am (UK)
Related stories
Dual flow alarm and rate indicator is ultrasonic
Roxspur Measurement and Control have released a new solid state flow switch, the UQS7 - an adjustable dual flow alarm with an additional digital flow rate indicator
Furnace and heat treatment monitoring systems
Brearley has a history of monitoring furnaces and heat treatment systems, up to the latest AMS2750D specification requirements for the monitoring of aerospace component heat treatment facilities
Typically a glass tube flowmeter will operate over a 10:1 flow range, and the fine control valve supplied with the frame will easily control all such flows.
Platon also manufacture the Platon FCV - a stand-alone multi-turn Fine Control Valve - which allows precision adjustment of fluid flows, suitable for use on gas flows up to 100Litres/minute (liquids to 3.5L/min), in piping systems typically using standard 1/4BSP (G1/4) connections: these are common in laboratories and pilot plants or sample/purge flow systems.
The Platon FCV gives precision control over a wide flow range, typically 100:1.
Further reading
Flush-faced miniature pressure transmitter
The latest Sensit pressure transmitter offers a small ceramic faced sensor that can be mounted flush with the inside wall of a tank or pipe, avoiding any problems from clogging and abrasion
High definition thermal imager is lower in cost
The innovative IRI4010R multi-purpose thermal imager from Roxspur, ideal for the thermographer and maintenance engineer alike, is now introduced at a lower cost than similar previous units
Special offer from Brearley on IR monitoring
During September Brearley are offering their innovative hand held infrared MicroRay Pro thermometer at just GBP70 each: and if you buy three or more, the price comes down to just GBP65 each
In a flow system, the pump or the storage system pressure will vary, either as the demand from other users changes, or as the fluid is discharged.
This can lead to a variation of the flow delivered, through the simple FCV control valve.
With sampling systems, the sampled flow conditions might change, or the sample analysis or collection and storage system might provide a variable back pressure, resulting in an undesirable change in the sample flow rate.
Many such site condition changes can be overcome, and a steady flow maintained, by using a simple mechanical flow controller, known as a Platon Flostat, such as the Model MN.
The MN Flostat is a mechanical device, which uses the flow pressure across an orifice to act against a spring loaded diaphragm, within the Flostat, to control the flow at a value preset using an integral multi-turn needle valve: typically the MN Flostat is used in series with the Platon NGX flowmeter to show the operator the actual flow rate being pre-set.
A differential pressure is required across the Flostat for it to function: the largest MN Flostats suitable for 1/4BSP applications can control gas flows from 8-100L/min and liquids from 0.25-3.5L/min, whereas the smallest range units control 0.005-5L/min gas and 0.002-0.2L/min water.
Once set, the flow rate will be maintained constant, subject to the differential pressure required being maintained across the Flostat: the constant flow rate will be visible on the NGX flowmeter.
Flostats are ideal for blending or dosing applications to maintain the required delivery of valuable gases or liquids, despite variations in the process line pressure.
Similarly, Flostats are ideal for use on gas sampling, purging or inert gas tank blanketing systems to maintain flow rate independent of the back pressure in the delivery vessel.
Bubbler type liquid level measurement systems benefit from improved accuracy and lower gas usage when fitted with a Flostat.
Larger Platon Flostats are available: even for as large as 4inch line sizes.
Such units have been used to maintain a constant flow of irrigation water into separate branch lines despite large variations in the supply pressure from the reservoir.
Other Flostats have been used to control the delivery of aviation fuel into aircraft tanks to a certain safe maximum rate, whatever power the generator driven pump might have been providing.
Because the Flostat is a mechanical controller, it requires no power, and there is no problem with using the device in a hazardous area or for the control of flammable liquids.
Special versions have been produced for higher pressure applications and for low pressure drop applications.
• Roxspur Measurement and Control: contact details and other news
• Email this article to a colleague
• Register for the free Processingtalk email newsletter
• Processingtalk Home Page
Search the Pro-Talk network of sites
