Product category:
Pressure measurement systems
News Release from: SensorsOne | Subject: Gauge/Absolute pressure choice
Edited by the Processingtalk Editorial
Team on 29 September 2006
How to decide between gauge and absolute
pressure?
Determining whether you need gauge or absolute reference pressure is as important as selecting the pressure range itself, particularly for low pressure measurements.
Determining whether you need gauge or absolute reference pressure is as important as selecting the pressure range itself, particularly for low pressure measurements If you get it wrong your measurements are going to be out by approximately 1 bar, which could be a huge error if you are working over a 10 bar range for example
This article was originally published on Processingtalk on 24 May 2006 at 8.00am (UK)
Related stories
Digital autozero and span makes calibration easier
SensorsONE is launching the NEW digital autozero and span option for the Gefran TK industrial pressure transmitter and the TPSA precision pressure transmitter
Add life to a pressure transmitter! Use a display
SensorsOne launches exclusively the NEW Gefran TDP loop powered plug-in display for pressure transmitters
Also if you have taken delivery of a pressure transducer with an incorrect pressure reference it will normally mean that the manufacturer will have to build a replacement, because the reference pressure often determines the base construction of the sensing element.
It will be a very generous manufacturer that replaces the sensor for you free of charge! The most common pressure reference is gauge pressure signified by a (g) after the pressure unit e.g 30 psig, which means that the pressure measured is the total pressure minus atmospheric pressure.
There are two types of gauge reference pressure: vented gauge (vg) and sealed gauge (sg), A vented gauge pressure transmitter for example allows the outside air pressure to be exposed to the negative side of the pressure sensing diaphragm, via a vented cable or a hole on the side of the device, so that it always measures the pressure referred to ambient barometric pressure.
Further reading
Low DP transmitter for use on wet and dirty gases
SensorsONE is adding the Ashdown Controls DRS low differential pressure transducer and transmitter for use with wet and dirty gases to its pressure sensor range
Pressure transmitters a click away from your door!
The popular Gefran TK industrial pressure transmitter is now available from stock and can be delivered within 72 hours via the SensorsONE Buy Online website or with a purchase order
Handy ATEX digital pressure test gauge
SensorsONE is adding the Keller LEO 2 digital pressure test gauge to the buy online pages of their dedicated pressure measurement website
Thus a vented gauge reference pressure sensor should always read zero pressure when the process pressure connection is held open to the air.
A sealed gauge reference is very similar except that atmospheric pressure is sealed on the negative side of the diaphragm.
This is usually adopted on high pressure applications such as in hydraulics, where atmospheric pressure changes will have a negligible effect on the accuracy of the sensor so venting is not necessary.
This also allows some manufacturers to provide secondary pressure containment as an extra precaution for pressure equipment safety, if the burst pressure of the primary pressure sensing diaphragm is exceeded.
There is another way of creating a sealed gauge reference and this is to seal a high vacuum on the reverse side of the sensing diaphragm.
Then by adjusting the electronics the output signal is offset by 1 bar so the pressure sensor reads close to zero when measuring atmospheric pressure.
A sealed gauge reference pressure transducer will never read exactly zero because atmospheric pressure is always changing and the reference in this case is fixed at 1 bar.
An absolute pressure measurement is one that is referred to absolute vacuum, which is absolutely the lowest pressure that the laws of physics will allow! The best example of an absolute referenced pressure is atmospheric or barometric pressure.
In order to produce an absolute pressure sensor the manufacturer will seal a high vacuum behind the sensing diaphragm.
Therefore if you hold open the process pressure connection of an absolute pressure transmitter to the air it will read the actual barometric pressure.
How do you know when to use an absolute pressure sensor or a gauge pressure sensor? This is not always straightforward but generally if you want to measure or control a pressure that is dependent on changes in atmospheric pressure, e.g the level of liquid in an open tank or the output pressure of an air compressor, you will need to use a (vented) gauge pressure instrument.
If you want to measure pressures that are not influenced by changes in atmospheric pressure, e.g leak testing a gas mains pipe, you would typically use an absolute pressure indicator.
• SensorsOne: contact details and other news
• Email this article to a colleague
• Register for the free Processingtalk email newsletter
• Processingtalk Home Page
Search the Pro-Talk network of sites
