Product category:
Trade Associations and Standards
News Release from: TUV Rheinland UK | Subject: SLIM
Edited by the Processingtalk Editorial
Team on 18 March 2005
New 'Simpler Legislation for the
Internal Market'
The new EMC directive 2004/108/EC was published in the Official Journal of the European Union, replacing the EMC Directive 89/336/EEC which became effective on 1st of January 1996
On 31st of December 2004, the new EMC directive 2004/108/EC was published in the Official Journal of the European Union, replacing the EMC Directive 89/336/EEC which became effective on 1st of January 1996 The new regulation encompasses the same objectives as the previous one, adding better definitions of the products, which need to be in compliance with the scope of the Directive, but also a clearer knowledge of the products excluded
This article was originally published on Processingtalk on 23 Apr 2004 at 8.00am (UK)
Related stories
CE mark recognition in the USA and Canada
In the US and Canada is the CE mark or certification of equipment by foreign testing organisations accepted? It is not comparable with the NRTL listing as required by OSHA and the local jurisdictions!
Export opportunities in the Russian Federation
UK Trade and Investment, the Government organisation which provides support for UK companies, believes that the Russian Federation continues to offer good opportunities for UK exporters
Also, with more detailed requirements, everything should now be much more understandable for the manufacturer, the buyer or any other third organisation implicated.
The new Directive has been written under the initiative "Simpler Legislation for the Internal Market SLIM" of the European Commission that adopted a comprehensive multi-annual programme in February 2003 to simplify and update the Community Legislation.
EMC Directive 2004/108/EC stipulates two major dates for its implementation.
Further reading
EN 61242 found insufficient by the EC
EN 61242 cable reels found to be lacking according to the European Commission opinion
Waste Electrical and Electronic Equipment
Due to the increasing amount of electronic and electrical waste, the Waste Electrical and Electronic Equipment Directive and the Restriction on Hazardous Substances Directive were enacted in 2002
The problems of non EMC compliant equipment!
The unreliable readings of fixed speed detection cameras in the Australian state of Victoria caused by poor installation and electromagnetic interference may cost up to AUS30 million
Firstly, all equipment already complying with the scope of the previous directive can be bought and sold until the 20th of July 2009.
Secondly, Member States shall adopt and publish the laws, regulations and provisions necessary to comply with this Directive by the 20th of July 2007.
This new directive covers both fixed installations and apparatus but excludes all equipment that is inherently benign from an electromagnetic compatibility point of view.
Regarding fixed installations; all machines and networks that may disturb or be disturbed by electromagnetic fields are also included.
Fixed installations can be defined as an assembly of multiple apparatus having the CE Marking and aimed at being used permanently in a specific location within the EU such as electricity and telecommunication networks or complex machinery.
Due to the nature of fixed installations, placing the CE mark on the equipment and creating a Declaration of Conformity are not required.
Requirements for fixed installations have been included.
Good engineering practices must be used and documented, the documents shall be held available for the relevant national authorities for as long as the fixed installation is in operation.
The directive is applicable to finished apparatus commercially available for the first time on the market, and states that for apparatus able to take different configurations, the EMC assessment shall look at these different configurations determined by the manufacturer who must prepare technical documentation providing proof of the conformity of the apparatus with the requirements of the Directive.
The apparatus must now be identified in terms of type, batch and serial number and carry the name and address of the manufacturer or the person placing it on the market.
Concerning the EC declaration of Conformity, it has now to be dated and contain Reference to this Directive, the identification of the equipment and the manufacturer, a dated reference to the standards to be provided in case of compliance claim, and the identity and signature of the signatory.
• TUV Rheinland UK: contact details and other news
• Email this article to a colleague
• Register for the free Processingtalk email newsletter
• Processingtalk Home Page
Search the Pro-Talk network of sites
