Product category:
Robots and positioning systems
News Release from: Wittmann UK | Subject: SmartRemoval
Edited by the Processingtalk Editorial
Team on 30 January 2008
Wittmann UK clients work Smarter!
Following the K 2007 exhibition in Dusseldorf last Autumn, there has been considerable demand for Wittmann automation products, both robots and software
Wittmann UK gets clients working Smarter Wittmann UK Managing Director Barry Hill says that following the K 2007 exhibition in Dusseldorf last Autumn, there has been considerable demand for Wittmann's automation products; robots and software 'With increased demand in all manufacturing industry for more from less, anything that can increase productivity in suppliers will be popular' said UK Managing Director Barry Hill
This article was originally published on Processingtalk on 11 Mar 2004 at 8.00am (UK)
Related stories
Greater range of temperature control from Wittmann
2004 will see Wittmann UK building sales of its Tempro Plus and Tempro Primus mould temperature controllers to plastics processors by offering a range of direct and indirect cooling options
Internet-controlled plastics production
The prospect of Internet-controlled plastics production management moves closer with WittLink, a Wittmann-developed system for monitoring automation equipment via an array of embedded web servers
The new Wittmann SmartRemoval technology fits that bill.
It represents a new method of part removal to reduce unproductive time within the moulding cycle.
The new "SmartRemoval" function monitors all the time relevant processes in parallel - no matter whether they are a result of the robot or the machine.
Further reading
Materials handling from the desktop via CanBus
The new M7 Teachbox system allows a single point of control of all the materials distribution through a typical plastics processing operation: conveying, vacuum pumps, hopper loaders, alarm units....
New option of dual hopper dryer system
Wittmann UK has expanded its Drymax C30 Series of materials dryers for the plastics processing sector in order to include the option of two drying hoppers, each with independent temperature control
Wittmann UK offers more with hopper loaders
Wittmann has announced a number of innovations for its range of vacuum loaders for central material handling systems for the plastics processing sector with the Feedmax "A" Series
In combination with the machine controller, the software optimises the takeout path for the robot in order to perform "SmartRemoval".
This development has been driven by continued processor demand for the reduction of takeout time or, in terms of the entire production cell, a reduction of the "unproductive time" between the end of the cooling process in the mould and the start of the next cycle.
The purpose of "SmartRemoval" is to completely eliminate the delay caused by the transfer of the electric signals from the takeout process.
Savings of up to 0.5s per cycle can be achieved with the new "SmartRemoval" function, which for a total cycle time of 5s corresponds to a time savings or increase in productivity of about 10%! "Le Mans start" is a well known concept from the car racing sport ("24 hours of Le Mans") and signifies in contrast to other start modes a start also defined by a signal, however, not from a standstill but during slow movement.
"SmartRemoval" is quite similar as the robot operator only needs to programme the start position above the mould as well as the takeout position for the hand-off of the finished parts - the rest (the calculation of the optimal possible movement between these two positions) will be automatically performed by the robot controller.
The correct adjustment must be made to the robot for the mould safety area on the Y-arm of the robot which may also be modified in the case of a mould change (EOAT change) where there is a difference in dimensions.
Once the robot is started in Automatic Mode several internal processes automatically take place to optimise the takeout time while constantly monitoring and adapting the operation, if necessary.
The robot monitors itself beginning with the very first cycle in automatic mode in order to calculate when the mould will open next, allowing the Y-axis to begin moving from the waiting position just before the mould has fully opened.
When it receives the signal from the machine that the mould is fully open, the Y-axis is already in position to enter the molding area, saving precious time.
But, if the signal is not received at the calculated time (for whatever reason), the robot will stop at the last possible point above the mould to avoid any damage.
Very similar is the synchronisation of the robot with the ejectors known as the "Move In" process.
Based on the preceding measurements the robot can start the ejector forward signal at a set time before reaching the takeout position thus, allowing the finished parts to be in position without waiting for the ejectors.
The "Move Out" process is based on a similar principle.
The best possible time to set the "Mould Close" signal is automatically calculated and the signal is sent to the machine before the robot has completely left the moulding area.
• Wittmann UK: contact details and other news
• Email this article to a colleague
• Register for the free Processingtalk email newsletter
• Processingtalk Home Page
Search the Pro-Talk network of sites
